The term “space bucket” was coined roughly seven years ago, but this indoor grow type is older.
Someone asked, ‘Could I grow marijuana in a bucket?’ This led to the question of ‘how to cultivate cannabis in a space bucket?’ and ‘how can you cultivate marijuana seeds in a space bucket?’
Space Bucket | Marijuana Growing Guide
Space buckets are an “entry-level” growing experience. In reality, most growers who adopt space buckets do not expect massive plant yields. We all have to start somewhere, don’t we? But that doesn’t mean that if you try hard enough, you won’t generate a lot. If you want to discover more, visit Seed Supreme or keep reading our space bucket grow guide.
Why Grow Weed in a Space Bucket?
Controlled Environment
Like grow tents and cabinets, space buckets provide you with complete control over many development elements such as lighting and air circulation.
Expanding in space Buckets enjoy the benefits of growing in a confined place, such as a closet. Among the advantages are:
- Protection against annoying insects and house mice.
- A clean atmosphere is maintained with the healthiest possible yield.
- Installing a drip system makes hydroponics cultivation simple.
The ideal technique to cultivate marijuana seeds in a space bucket is using a hydroponics space bucket; however, you need some experience designing a hydroponics system.
Small Size
It is entirely up to you how large you want your space buckets to be when you buy marijuana seeds for your harvest. Room buckets are often small and take up little space, hence the name. You can store these buckets in your closet or the trunk of your car, away from prying eyes. It’s simple to conceal space buckets. Hide them behind a clothes curtain in a closet or a corner.
Growers can make many space buckets due to the very minimal area they take up, allowing them to grow marijuana in different stages for back-to-back harvests. This approach is known as the endless harvests method by experienced growers, and it is commonly seen in grow tents. You save money on a setup by employing space buckets.
Budget-Friendly Solution
Space buckets can be purchased at a reasonable cost when constructing a basic setup. You will require the following items:
- CFLs
- A bucket size of your choice
- CPU fans
How much would this set you back? A single space bucket would not set you back more than $100.
However, if you want to get the best yield and a large amount of it, you can switch from CFLs to LEDs and replace the bucket with a trash bin or even a drum.
Space buckets are cheap to construct and keep because they don’t take up much room. They’re also ideal for first-time growers with DIY knowledge, as building a space bucket is simple.
How to Build Your Own Space Bucket Grow
Gather Your Materials
To begin creating your space bucket, we recommend the following items:
- 2 five-gallon buckets
- 1 five-gallon bucket lid
- 4 CFLs or 1 Full-spectrum LED grow light
- 2 CPU fans
- 1 Power strip
- 1 Timer
- 4 6mm bolts with nuts and washers
- 1 1m thin rope
- 1 aerosol glue
- 1 tube silicone sealant
- 1 210x120cm mylar film
- 1 roll of duct tape
First and foremost, safety! Our space bucket grow guide includes all of the safety equipment you’ll need to get started. You’ll need:
- Safety glasses and hardware gloves
- Rotary tool
- Drill
- Razor blade or Exacto knife
- Measuring tape
- Permanent marker
Prepare for Drainage
After completing the proper safety gear, you will:
- Measure 8cm from the bottom of the two 5 gallon buckets.
- Using your permanent marker, make a horizontal line.
- Using your rotary tool, remove the bucket’s bottom.
The top half of your space bucket is now used for the lights, and the bottom half serves as a drip tray.
- Drill 12 properly spaced holes in the bottom of the second 5-gallon bucket. If there is a handle, remove it.
- To cover, place the other bucket on top. This bucket serves as the “cover” that holds the buckets together.
Now comes the exciting part. To begin, drill a hole slightly below the rim of each quadrant of the bottom bucket to link the top and bottom buckets. The bolts should then be inserted into the holes and secured with nuts and washers.
Place the top bucket on top of the lower bucket and indicate the location of the bolts.
Next, draw an upside-down “L” shape by measuring 4cm up and 4cm wide. Cut a wide channel with your rotary tool once you have the upside-down L shape. For your space bucket, you now have a simple twist lock.
Add Fans and Lightning
Install CPU fans for ventilation by measuring the fan housing and drawing apertures. To ensure a suitable fit, cut the exact form of your bottom bucket.
You now have an intake fan cutout. Make the identical cutout for the second CPU fan (the exhaust fan) on the top bucket.
Install the lights after installing the ventilation system. 4 CFL bulbs or LED grow light strips are required. Line the interior of your bottom bucket lid with these. If you use CFL bulbs, you must drill four additional holes in the lid to accommodate the electrical components. You should also cut a fan hole in the lid for proper air circulation.
Appropriate Sealing
Use duct tape and rope to seal your space bucket. Place it between the bottom bucket’s rim and the bolts. Check to see if the seal fits properly. If it happens, keep adding layers of duct tape until the gap between the two buckets is closed and light from the outside does not flow into your space bucket.
It would help if you also lined the inside of your space bucket with Mylar film at this time. Spray the inside with aerosol adhesive and adhere to the Mylar film. Once everything is sealed, reopen the CPU fan cutouts with a razor or Exacto knife.
Install and Test Fans
When wiring your space bucket, remember that the direction of the grills affects the intake and exhaust fans. So make sure your intake fan’s grills face inside the bucket, and your exhaust fan’s grills face outside.
No worries about gaps. Close any gaps left by the cuts where your CPU fan housing was installed. After installation, test everything. Plug in the fans and the timer lights.
